Diode-led REIGN Button/Full Slide Dimmer Manual do Utilizador descarregar pdf

IG051514-1.1

1.877.817.6028

www.DiodeLED.com

INSTALLATION GUIDE

[email protected] www.DiodeLED.com

1 OF 3

REIGN™ 12-24V BUTTON/FULL SLIDE DIMMER SWITCH

DO NOT CONNECT DIRECTLY TO HIGH VOLTAGE POWER!

Read all warnings and installaon instrucons thoroughly.

WARNING

Safety & Warnings

Prior to installaon, verify all components are a compable system. Congure and pre-test your LED system prior to permanent installaon to ensure all

components are operang correctly. Install in accordance with the NEC and local regulaons.

• Install in accordance with the Naonal Electric Code, and local

regulaons.

• This product is intended to be installed and serviced by a qualied,

licensed electrician.

• DO NOT connect directly to high voltage power. Install with a compable

Class 2 constant voltage LED driver (power supply).

• Only install compable LED drivers and xtures. Contact technical

support or visit the product page for compable products.

• This product is rated for indoor installaon and is not protected against

moisture.

• Proper heat dissipaon will prolong the working lifespan of this product.

Install in a well-venlated area free from explosive gases and vapors.

• Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Inadequate wire installaon could overhead wires, and cause a re.

• Do not modify or disassemble this product beyond instrucons or the

warranty will be void.

Installation

WARNING

Shock Hazard. May result in serious injury or death.

Turn OFF High Voltage AC Power at the main breaker.

Determine Locaons to Install 3 Main Components.

Refer to the ‘System Diagram.’

OFFOFFOFF

ONON

OFFOFF

ONON

Ensure applicable wire is installed between driver, xture, and any

controls in between. When choosing wire, factor in voltage drop,

amperage rang, and type (in-wall rated, wet locaon rated, etc.).

Quick Specs

Input / Output Voltage 12-24VDC Constant Voltage

Ambient Temperature † -40°F ~ 140°F (-40°C ~ 60°C)

Minimum Load See driver specs for min load.

Maximum Load 100W (12V & 24V)

Included Models

1150-** (Buon Slide)

1151-** (Full Slide)

† Do not install product in an environment outside the listed ambient

temperature.

** Indicates color nish.

1) Driver

2) REIGN Dimmer 3) Fixture

Remove Exisng Wall Plate and Switch.

V+ (Red)

OUTPUT

V+ (Red)

INPUT

V- (Black)

OUPUT

V- (Black)

INPUT

Cap exisng ground wires.

Wire REIGN Dimmer Between Driver and Fixture. Only Use

Copper Wiring. DO NOT CONNECT TO HIGH VOLTAGE POWER.

• Aach INPUT of dimmer to driver.

• Aach OUTPUT of dimmer to LED xture.

See ‘Wiring Connecons’ below & ‘System Diagram.’

Wiring Connections

DO NOT CONNECT

TO HIGH VOLTAGE

Dry Location Only

12V

24V

1 2 3

Resumo do Conteúdo

Página 1 - Wiring Connections

IG051514-1.11.877.817.6028www.DiodeLED.comINSTALLATION GUIDE®[email protected] www.DiodeLED.com1 OF 3REIGN™ 12-24V BUTTON/FULL SLIDE DIMMER SWITCHDO

Página 2 - System Diagram

IG051514-1.11.877.817.6028www.DiodeLED.comINSTALLATION GUIDE®[email protected] www.DiodeLED.com2 OF 3REIGN™ 12-24V BUTTON/FULL SLIDE DIMMER SWITCHIns

Página 3 - QUESTIONS?

IG051514-1.11.877.817.6028www.DiodeLED.comINSTALLATION GUIDE®[email protected] www.DiodeLED.com3 OF 3REIGN™ 12-24V BUTTON/FULL SLIDE DIMMER SWITCHTro

Comentários a estes Manuais

Sem comentários

Diode-led REIGN Button/Full Slide Dimmer Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Iluminação Diode-led REIGN Button/Full Slide Dimmer. Diode LED REIGN Button/Full Slide Dimmer User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Iluminação Diode-led REIGN Button/Full Slide Dimmer