Diode-led RGB Zone Control Manual do Utilizador descarregar pdf (Página 2)

1.877.817.6028

www.DiodeLED.com

[email protected] www.DiodeLED.com

INSTALLATION GUIDE

2 OF 4

RGB ZONE COLOR CONTROLLER

Operation

Mount RGB Receiver to Surface. See ‘Wiring Connecons’, use

applicable screws.

Aach Lighng Load and Driver. Only use copper wiring.

Reference ‘Wiring Connecons’ located further in guide for

visual. Use a mini athead screwdriver for aaching wires to

terminal ports. Terminals t up to 12AWG solid-core copper

wire. Verify a compable constant voltage driver is installed.

Install Addional Components, Verify Connecons, and Turn

Main Power ON at Breaker.

OFFOFFOFF

ONON

OFFOFF

ONON

If system remains unresponsive

or is working improperly, turn OFF

main power at breaker and verify

all connecons. Review the ‘Wiring

Connecons’ or ‘Troubleshoong’

secons for further details.

Charging the Zone Remote

• A flashing red indicator light on the Zone Remote implies a low battery.

• To charge the Zone Remote, connect the included USB 2.0A/Mini-B cable to the remote and to any USB compable computer or mobile charger

with a USB port (not included).

• Press the power buon on the Zone Remote and a blue indicator light will ash connuously to indicate charging. Once the indicator light turns

green, charging is complete.

Reseng Receiver to Factory Sengs

• To reset a single receiver, long press the ‘Power’ buon on the receiver (you will hear an inial beep). Connue holding for >8 seconds unl the

receiver long beeps. The receiver has now been reset to factory sengs.

Pairing the Zone Remote with a Zone Receiver. The Zone

Remote can control up to 10 dierent Zone Receivers. Only one

remote can be paired to each receiver. To pair the Zone Remote

with a Zone Receiver:

• POWER: Turns the Zone Receiver and Zone Remote ON/OFF.

• PAUSE: A quick press of the PAUSE key freezes the current MODE. Holding the PAUSE key on the Zone Remote for 3 seconds will turn the sound

on all Zone Receivers ON/OFF.

• MODE: Cycles through 18 pre-programmed MODES. Holding MODE for 3 seconds unl a long beep sounds will cycle the MODE to No. 1 of the

Mode Descripon Chart and adjust the SPEED to 5.

• SPEED: Press to cycle through 8 dierent SPEEDS of any current MODE. Holding SPEED for 3 seconds unl a buzzer sounds will adjust the SPEED

to 5.

• BRIGHTNESS: Press to cycle through 8 BRIGHTNESS levels of any current MODE or single color. Holding BRIGHTNESS will gradually increase light

intensity. A quick double-beep indicates maximum brightness if sound is turned on (see PAUSE key for turning sound ON/OFF).

• COLOR ADJUSTMENT WHEEL: Adjusts stac colors. The LED indicator in the center of the COLOR ADJUSTMENT WHEEL displays the current stac

color selected.

• ZONE CONTROL: Selects a specic zone to control (1-10). To choose all 10 zones press “

” twice. To control a selected number of zones in sync

press “

+ any numeral +

”. For example, if you would like to control zones 1, 5, & 9 together, press “

159

”.

• SAVED SCENE: Holding M1 or M2 (Memory 1 or Memory 2) for 3 seconds will save the current stac color or MODE to a SAVED SCENE. To indicate

a saved scene the zone receiver will long beep and a red indicator light will ash 3 mes on the Zone Remote.

1. Turn on the Remote and Receiver by pressing the power buon on

each device.

2. Next, press and hold the power buon on the Receiver for 3 seconds

unl you hear a short beep, and connue to hold. Once the Receiver

short beeps immediately hold down a zone number of your choice

(1-10) on the Remote. Ensure to connue holding the power buon on

the Receiver aer it beeps, and then simultaneously choose a zone on

the Remote.

3. To indicate pairing, the Receiver will long beep and a green indicator

light will ash 3 mes on the Remote.

See the online product page for video

tutorials or contact technical support.

Need Addional Assistance?

IG060914-1.2

1 2 3 4

1.877.817.6028 1
QUESTIONS? 4

Comentários a estes Manuais

Sem comentários

Diode-led RGB Zone Control Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Iluminação Diode-led RGB Zone Control